国产精品免费久久久久软件,亚洲乱码精品久久久久..,国产在线精品观看免费观看,日韩欧美精品综合中文字幕

公司新聞

當前位置:首頁 > 新聞中心 > 公司新聞

怎么判斷羅茨風機齒輪磨損程度?

來源:http://m.jz418.cn/   日期:2021-07-23   瀏覽量:0
TAG:山東制氮機,山東干燥機,山東螺桿鼓風機,山東空壓機,山東自動排水器
一般羅茨風機都是不允許反轉的(因為進氣口跟排氣口的間隙設置不一樣),所以羅茨風機都需要在排氣端設置單向閥。也就是允許風從羅茨風機輸入到管道系統,防止羅茨鼓風機突然停機,羅茨風機而系統的氣體收到系統壓力的作用,回流沖擊羅茨風機造成羅茨風機反轉,損壞羅茨鼓風機另外,幾臺羅茨鼓風機并聯運行的時候,假設其中一臺不工作,那么單向閥也可以防止排氣端的氣體通過這臺沒有使用的羅茨鼓風機,造成其反轉損壞。
Generally, the roots blower is not allowed to reverse (because the gap setting between the air inlet and the exhaust port is different), so the roots blower needs to set a check valve at the exhaust end. In other words, it allows the air to be input from roots blower to the pipeline system to prevent the roots blower from sudden shutdown. The roots blower and the gas in the system receives the effect of system pressure, and the backflow impacts the roots blower, causing the roots blower to reverse and damage the roots blower. In addition, when several roots blowers operate in parallel, it is assumed that one of them does not work, Then, the check valve can also prevent the gas at the exhaust end from passing through the unused roots blower, resulting in reverse damage.
總而言之,就是保護羅茨風機不反轉.按結構形式分:立式型羅茨風機兩轉子中心線在同一垂直水平面內,氣流水平進,水平出;臥式型羅茨風機兩轉子中心線在同一水平面內,氣流垂直進,垂直出。所說的風葉相碰。
In short, it is to protect the roots blower from reverse rotation. According to the structural form, the center lines of the two rotors of the vertical roots blower are in the same vertical horizontal plane, and the air flow enters and exits horizontally; The center lines of two rotors of horizontal roots blower are in the same horizontal plane, and the air flow enters and exits vertically. The wind leaves collide.
絕大部分是軸承間隙變大引起的,如果更換同步齒輪不行,建議使用質量較好的軸承,不用進口的最起碼也得用瓦軸或洛軸的高速軸承,羅茨風機齒輪的磨損可以根據齒輪咬合間隙判斷,如果齒輪磨損超限,可以將兩個同步齒輪翻面處理,這樣齒輪就可以延長一倍使用壽命,調整兩風葉間隙時一定要用塞尺沿風葉長度測定4個點以上,羅茨鼓風機保證整個長度上的間隙均勻、一致。
Most of them are caused by the larger bearing clearance. If it is not possible to replace the synchronous gear, it is recommended to use bearings with better quality. If it is not necessary to import, at least the high-speed bearings of bearing bush or Luo shaft should be used. The wear of Roots blower gear can be judged according to the gear engagement clearance. If the gear wear exceeds the limit, the two synchronous gears can be turned over, In this way, the service life of the gear can be doubled. When adjusting the clearance between the two blades, be sure to use a feeler gauge to measure more than 4 points along the length of the blades. Roots blower ensures that the clearance on the whole length is uniform and consistent.

上一篇:教你正確選擇空壓機排氣量
下一篇:怎么樣評判自己需要哪種PSA制氮機?